Check Point Cpac-Tr-100lr-Ssm160-Qsfp28 Compatible 100gbase-Lr4 Qsfp28 1310nm 10km Dom Optical Transceiver Module

100Gb/s QSFP28 LR4 10km TransceiverPRODUCT FEATURES Compliant with 100GBASE-LR4 Support line rates from 103.125 Gbps to 111.81 Gbps Integrated LAN WDM TOSA / ROSA for up to 10 km reach over SMFDigital Diagnostics Monitoring InterfaceDuplex LC optical receptacle No external reference clock Electrica......

Send Inquiry

Product Description

100Gb/s QSFP28 LR4 10km Transceiver

PRODUCT FEATURES

Compliant with 100GBASE-LR4
Support line rates from 103.125 Gbps to 111.81 Gbps
Integrated LAN WDM TOSA / ROSA for up to 10 km reach over SMF
Digital Diagnostics Monitoring Interface
Duplex LC optical receptacle
No external reference clock
Electrically hot-pluggable
Compliant with QSFP28 MSA with LC connector
Case operating temperature range:0°C to 70°C
Power dissipation < 3.5 W

APPLICATIONS

100G Ethernet &100GBASE-LR4
ITU-T OTU4

STANDARD

Compliant to IEEE 802.3ba, IEEE 802.3bm and 100G LR4
Compliant to SFF-8436

General Description
LAQ2-8429-LR optical Transceiver integrates receiver and transmitter path on one module. In the transmit side, four lanes of serial data streams are recovered, retimed, and passed to four laser drivers. The laser drivers control 4 Distributed Feedback Laser (DFB) with center wavelength of 1296 nm, 1300nm, 1305nm and 1309 nm. The optical signals are multiplexed to a single -mode fiber through an industry standard LC connector. In the receive side, the four lanes of optical data streams are optically de-multiplexed by the integrated optical de-multiplexer. Each data stream is recovered by a PIN photo-detector and trans-impedance amplifier, retimed. This module features a hot-pluggable electrical interface, low power consumption and MDIO management interface.
The product is designed with form factor, optical/electrical connection and digital diagnostic interface according to the QSFP28 Multi-Source Agreement (MSA) and compliant to IEEE 802.3bm.
Absolute Maximum Ratings

Parameter	Symbol	Min.	Typ.	Max.	Unit	Note
Storage Temperature	Ts	-40	-	85	ºC
Relative Humidity	RH	5	-	95	%
Power Supply Voltage	VCC	-0.3	-	4	V
Signal Input Voltage		Vcc-0.3	-	Vcc+0.3	V

Recommended Operating Conditions

Parameter	Symbol	Min.	Typ.	Max.	Unit	Note
Case Operating Temperature	Tcase	0	-	70	ºC	Without air flow
Power Supply Voltage	VCC	3.13	3.3	3.47	V
Power Supply Current	ICC	-		1060	mA
Data Rate	BR		25.78125		Gbps	Each channel
Transmission Distance	TD		-	10	km
Coupled fiber	Single mode fiber					9/125um SMF

Optical Characteristics

Parameter	Symbol	Min	Typ	Max	Unit	NOTE
Transmitter
Wavelength Assignment	λ0	1294.53	1295.56	1296.59	nm
	λ1	1299.02	1300.05	1301.09	nm
	λ2	1303.54	1304.58	1305.63	nm
	λ3	1308.09	1309.14	1310.19	nm
Total Output. Power	POUT			10.5	dBm
Average Launch Power Per lane		-4.3		4.5	dBm
Spectral Width (-20dB)	σ			1	nm
SMSR		30			dB
Optical Extinction Ratio	ER	4			dB
Average launch Power off per lane	Poff			-30	dBm
RIN	RIN			-128	dB/Hz
Output Eye Mask definition {X1,X2,X3,Y1,Y2,Y3}	{0.25,0.4,0.45,0.25,0.28,0.4}
Receiver
Rx Sensitivity per lane	RSENS			-10.6	dBm	1
LOS De-Assert	LOSD	-30			dBm
LOS Assert	LOSA			-12	dBm
Input Saturation Power (Overload)	Psat			4.5	dBm
Receiver Reflectance	Rr			-26	dB

Notes:

Measured with a PRBS 2³¹-1 test pattern, @25.78Gb/s, BER<10^-12.

1. Electrical Characteristics

Parameter	Symbol	Min	Typ	Max	Unit	NOTE
Supply Voltage	Vcc	3.13	3.3	3.47	V
Supply Current	Icc			1060	mA
Transmitter
Input differential impedance	Rin		100		Ω	1
Differential data input swing	Vin,pp	180		1000	mV
Transmit Disable Voltage	VD	Vcc-1.3		Vcc	V
Transmit Enable Voltage	VEN	Vee		Vee+ 0.8	V	2
Receiver
Differential data output swing	Vout,pp	300		850	mV	3
LOS Fault	VLOS fault	Vcc-1.3		VccHOST	V	4
LOS Normal	VLOS norm	Vee		Vee+0.8	V	4

Notes:

Connected directly to TX data input pins. AC coupled thereafter.
Or open circuit.
Into 100 ohms differential termination.
Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.

1. Pin Assignment

Figure 1---Pin out of Connector Block on Host Board

Pin	Symbol	Name/Description	NOTE
1	GND	Transmitter Ground (Common with Receiver Ground)	1
2	Tx2n	Transmitter Inverted Data Input
3	Tx2p	Transmitter Non-Inverted Data output
4	GND	Transmitter Ground (Common with Receiver Ground)	1
5	Tx4n	Transmitter Inverted Data Input
6	Tx4p	Transmitter Non-Inverted Data output
7	GND	Transmitter Ground (Common with Receiver Ground)	1
8	ModSelL	Module Select
9	ResetL	Module Reset
10	VccRx	3.3V Power Supply Receiver	2
11	SCL	2-Wire serial Interface Clock
12	SDA	2-Wire serial Interface Data
13	GND	Transmitter Ground (Common with Receiver Ground)
14	Rx3p	Receiver Non-Inverted Data Output
15	Rx3n	Receiver Inverted Data Output
16	GND	Transmitter Ground (Common with Receiver Ground)	1
17	Rx1p	Receiver Non-Inverted Data Output
18	Rx1n	Receiver Inverted Data Output
19	GND	Transmitter Ground (Common with Receiver Ground)	1
20	GND	Transmitter Ground (Common with Receiver Ground)	1
21	Rx2n	Receiver Inverted Data Output
22	Rx2p	Receiver Non-Inverted Data Output
23	GND	Transmitter Ground (Common with Receiver Ground)	1
24	Rx4n	Receiver Inverted Data Output	1
25	Rx4p	Receiver Non-Inverted Data Output
26	GND	Transmitter Ground (Common with Receiver Ground)	1
27	ModPrsl	Module Present
28	IntL	Interrupt
29	VccTx	3.3V power supply transmitter	2
30	Vcc1	3.3V power supply	2
31	LPMode	Low Power Mode
32	GND	Transmitter Ground (Common with Receiver Ground)	1
33	Tx3p	Transmitter Non-Inverted Data Input
34	Tx3n	Transmitter Inverted Data Output
35	GND	Transmitter Ground (Common with Receiver Ground)	1
36	Tx1p	Transmitter Non-Inverted Data Input
37	Tx1n	Transmitter Inverted Data Output
38	GND	Transmitter Ground (Common with Receiver Ground)	1

Notes:
1. GND is the symbol for signal and supply (power) common for QSFP28 modules. All are common within the QSFP28 module and all module voltages are referenced to this potential unless otherwise noted. Connect these directly to the host board signal common ground plane.
2. VccRx, Vcc1 and VccTx are the receiving and transmission power suppliers and shall be applied concurrently. Recommended host board power supply filtering is shown below. Vcc Rx, Vcc1 and Vcc Tx may be internally connected within the QSFP28 transceiver module in any combination. The connector pins are each rated for a maximum current of 500mA.

1. Digital Diagnostic Functions

LAQ2-8429-LR support the 2-wire serial communication protocol as defined in the QSFP28 MSA. Which allows real-time access to the following operating parameters:

Transceiver temperature
Laser bias current
Transmitted optical power
Received optical power
Transceiver supply voltage

       It also provides a sophisticated system of alarm and warning flags, which may be used to alert end-users when particular operating parameters are outside of a factory-set normal range.
       The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller inside the transceiver, which is accessed through the 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL pin) is generated by the host. The positive edge clocks data into the QSFP28 transceiver into those segments of its memory map that are not write-protected. The negative edge clocks data from the QSFP28 transceiver. The serial data signal (SDA pin) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. The 2-wire serial interface provides sequential or random access to the 8 bit parameters, addressed from 00h to the maximum address of the memory.
       This clause defines the Memory Map for QSFP28 transceiver used for serial ID, digital monitoring and certain control functions. The interface is mandatory for all QSFP28 devices. The memory map has been changed in order to accommodate 4 optical channels and limit the required memory space. The structure of the memory is shown in Figure 2 -QSFP28 Memory Map. The memory space is arranged into a lower, single page, address space of 128 bytes and multiple upper address space pages. This structure permits timely access to addresses in the lower page, e.g. Interrupt Flags and Monitors. Less time critical entries, e.g. serial ID information and threshold settings, are available with the Page Select function. The structure also provides address expansion by adding additional upper pages as needed. For example, in Figure 2 upper pages 01 and 02 are optional. Upper page 01 allows implementation of Application Select Table, and upper page 02 provides user read/write space. The lower page and upper pages 00 and 03 are always implemented. The interface address used is A0xh and is mainly used for time critical data like interrupt handling in order to enable a "one-time-read" for all data related to an interrupt situation. After an Interrupt, IntL, has been asserted, the host can read out the flag field to determine the effected channel and type of flag.
       For more detailed information including memory map definitions, please Contact our sales representatives.